news & press

Air angled finish nailers are invaluable tools for finish carpenters and woodworkers. Here are 6 tips to help you get the most out of your angled finish nailer.

What is an Angled Finish Nailer?

An angled finish nailer is a pneumatic nail gun designed specifically for installing trim and molding. The nailer's head is set at an angle, usually around 34 degrees, which allows it to fit into tight corners and reach into narrow spaces. Angled nailers are ideal for toe-nailing, angled nailing, and connecting workpieces at anything other than 90 degrees.

Key Uses for Angled Finish Nailers

· Installing door/window casings and trim

· Attaching baseboard and crown molding

· Securing decorative beams or trims

· Building furniture and cabinetry  

· Crafting picture frames and smaller woodworking projects

The angled discharge suits the wide range of nailing applications required for trim, molding, cabinetry, furniture assembly, and specialty woodworking. For toe-nailing, securing door or window casings at corners, and connecting workpieces with anything other than a straight shot, an angled nailer is the best tool for the job.

Tips for Angled Finish Nailer 

Use a Nailer Gauge or Depth Adjustment

One of the keys to getting proper results with an angled finish nailer is controlling the nail depth. Most models have an adjustment dial or gauge that allows you to set nail depth based on your material thickness.

For example, with thin 3/4" trim you'll want a more shallow depth setting. For nailing into thicker stock, increase the depth accordingly. Setting the proper depth helps the nails sink below the surface without poking through the other side.

Use a Nail Size Matched to Your Material

Angled finish nailers drive many different nail lengths and gauges. Matching the nail size to your work material is important. Smaller 16 or 18 gauge nails are designed for nailing thin moldings and trims. Going too large can cause unsightly splitting.

For thicker stock or layering trim, you can move up to 15 gauge nails around 2" for more holding power. Always pick a nail that will fully sink into the material without poking through.

Beware of Overdriving

It's easy to overdrive nails with the power of a pneumatic nail gun. Overdriving occurs when the nail sinks too deeply into the material, causing damage below the surface. On trim and woodwork, this can cause cracking, splitting, and indentations.

The key is to let up on power as the nail nears flush. Pull back slightly just before firing to avoid double hits. Overdriving takes practice to prevent, so consider using a nail set to countersink nails and disguise any minor overdriving.

Angle the Nailer Properly

Since angled finish nailers have an offset head, you need to position the nailer at the proper angle to fire straight into the workpiece. If the head is tilted too far either way, nails will drive off-center and cause splintering.

Keep the Nosepiece Against the Working Surface

For accurate results, it's important to keep the nailer's nosepiece pressed firmly against the working surface as you drive nails. This keeps the fastener shooting straight into the material. Even slight gaps can allow nails to drive off-target.

For trim work, brace the nailer's roller guide against the wall as you work to maintain steady contact. If nailing vertically, be ready to support the weight of the nail gun to avoid slipping. Keeping the nose flush takes a little finesse, but prevents crooked or skewed nails.

Watch for Nail Jams

To help avoid jams, don't tilt or twist the nailer while firing, which can bend strips. Use the recommended gauge and length nails for best performance. Old or damp nails also tend to jam more frequently. Finally, don’t press downward too hard, which can crush nail strips. With care, jams are preventable.

Angled nail guns are a must-have for finish carpenters, remodelers, woodworkers, and cabinet installers. The RONGPENG DA64R 15 Gauge Angled Finish Nailer is an useful tool for detailing and finish work. 

High strength alum alloy die casting body. One piece drive pin working life is more 0.15 millions times. Nail head and drive pin have be heat treated by Ipsen which import from Germany.

It drives 15 gauge finish nails from 1-1/4" to 2-1/2" in length. Spacious magazine holds up to 100 nails. Ideal for interior & exterior finish & trim, furniture, cabinet work, staircases, base boards, shoe & crown molding, window casing, chair rail molding, etc. 

Model: DA64R

Dimension: 330X320X80mm

Weight: 2.09kg

Required pressure: 80-120psi

Max.pressure: 120PSI(8.3bar)

Nail Capacity: 100pcs

RONGPENG has quickly risen to become an unrivaled global producer of air-powered devices including air tools, air spray gun, air nailer, airless paint sprayer, and etc.

RONGPENG seeks independent sales agent to represent and market our industry-leading pneumatic tools. We support OEM, ODM, OBM customization, small order quantity is acceptable and samples are available.

Make any cooperation possible. Any services related to the product, inquire with us now! Rongpeng@Rongpeng.Com