news & press

The preferred tools for car respraying are LVLP spray guns. This specialized tool allows for maximum control and efficient paint transfer when applying high-quality coatings to any vehicle surface.  In your home garage or workshop, you can use an LVLP gun to paint your car or truck with a flawless finish that looks like it just left the factory.

Why Use an LVLP Spray Gun for Car Painting?

LVLP spray guns are ideal for painting cars at home. Unlike high pressure HVLP guns, LVLP sprayers use lower air pressure (less than 10 PSI). The low pressure atomizes the paint into finer droplets that go on wetter for better flow out. Plus, LVLP guns are more forgiving compared to high pressure models. You can get closer to the surface without causing runs.

Another advantage of using an LVLP spray gun is that it allows for a higher level of control over the paint flow and air pressure. This means that you can achieve a smooth, even coat without the risk of overspraying or wasting paint, making them more environmentally friendly and cost-effective. For automotive painting, an LVLP spray gun gives you the control you need for a flawless finish. 

What You Need Before You Start?

Before you begin painting your car with an LVLP spray gun, there are several materials you'll need to gather. These include:

A properly prepared surface: Before you start painting, make sure the car's surface is clean, dry, and free of any debris or old paint. Use a degreaser to clean the surface, and then sand it lightly to create a smooth finish.

Paint: Use high quality single stage or basecoat clearcoat automotive paint. Make sure to select a color that matches your car's original color or choose a new color that you prefer.

LVLP spray gun: Invest in a high-quality LVLP spray gun designed for car painting. Look for a gun with adjustable air pressure and paint flow controls.

Air compressor: You'll need an air compressor to power the LVLP spray gun. LVLP guns require 4-6 CFM at no more than 10 PSI.

Safety equipment: Wear protective gear such as a mask, gloves, and eye protection when painting.

Paint booth or well-ventilated area: Paint in a well-ventilated area or in a paint booth to prevent overexposure to paint fumes and to contain the paint particles.

Spray the Basecoat Paint

The basecoat provides color for your paint job. For solid colors, you'll need just a basecoat. For metallic colors, you'll apply a subsequent clearcoat. 

Thoroughly stir the basecoat color before straining it into your spray gun. LVLP guns are ideal for basecoats because they atomize paint into a fine mist that helps metallic flakes orient properly. 

Maintain consistent distance and overlap your strokes to ensure even coverage. Apply 2-3 medium wet coats until you achieve your desired color intensity, allowing proper flash time between coats.

Apply the Clearcoat

The clearcoat provides a glossy, protective layer over your basecoat. It's essential when using metallic paints, but also gives an extra layer of UV protection for solid colors. Mix the clearcoat well and strain it into your spray gun. 

Keep your distance closer with clearcoat, around 6 inches from the surface. Apply 2-3 medium wet coats of clearcoat, allowing each coat to flash for 5-10 minutes before applying the next. Not to apply one thick coat, as this can cause drying problems. Allow the clearcoat to cure overnight before wet sanding and buffing.

Experience the precision of LVLP spray gun with the RONGPENG R500. This high-end spray gun gives you complete control and flawless results for all your automotive painting projects. The desired pattern,volume of fluid output and fine atomization can easily be obtained by regulating the pattern adjusting knob, fluid adjusting knob and air adjusting knob. Painters can adjust the inlet pressure and the painting distance according to the paint used,get the perfect results in any situation.

Stainless steel needle and nozzle accommodate a variety of coatings. Precise machined air cap set. Air Volume, paint volume and spraying pattern adjustable. New ergonomic designed handle for comfortable grip. Soft, super-fine mist suitable for all kinds of surface.

S.S nozzle and needle,brass air cap. Corrosion resistant PE cup. Gun body can bear quadrupling working pressure. Paint utilization rate can reach 65%. Trigger with 2 gears, the first for dust cleaning, second for painting. The RONGPENG R500 LVLP Spray Gun is ideal for automotive, woodworking, marine and industrial applications.

Standard Nozzle Size:φ1.5mm

Optional Nozzle Size:φ1.3 , φ1.7, φ2.0

Spraying width:180-280mm

Air Consumption:3.0-3.9cfm

Operating Pressure:2.0-3.5 bar

Paint Capacity:600cc

Flow Rate:140-190 ml/min

RONGPENG has quickly risen to become an unrivaled global producer of air-powered devices including air tools, air spray gun, air nailer, airless paint sprayer, and etc.

RONGPENG seeks independent sales agent to represent and market our industry-leading pneumatic tools. We support OEM, ODM, OBM customization, small order quantity is acceptable and samples are available.

Make any cooperation possible. Any services related to the product, inquire with us now! Rongpeng@Rongpeng.Com