news & press

One of the key tools for installing wall-to-wall carpeting is an air-powered stapler, which allows you to securely fasten the carpet to tack strips along the edges of the room. If you're new to using staplers for flooring installation, following some basic beginner guidelines will set you up for success.

Choosing an Air-Powered Stapler

When it comes to stapling down wall-to-wall carpeting, you'll want a sturdy pneumatic tool designed specifically for flooring installation. Heavy Duty 18-Gauge Narrow Crown Air Stapler are specially calibrated to properly penetrate tack strips and backings with 3/8" to 9/16" leg lengths. Look for comfortable grip handles and anti-slip rubber feet for easier control, an automatic fastener advance system also prevents jams by always feeding the next staple.

Preparing for Installation

Get all your supplies lined up before starting on carpet installation with a stapler. You'll need a tape measure, carpet knife, knee kicker tool, seam iron, wall trimmer tool, plus seam tape and proper floor adhesives.

Make sure to clear furniture and prep the subfloor carefully by fixing uneven areas, then applying adhesive primer. Always follow the carpet manufacturer’s recommendations for proper tack strip positioning as well. Place full strips 2 inches from walls around the perimeter, plus 8 inch strips halfway under any doors.

When you unpack the new carpet, allow it to relax in the room for 24 hours at normal living temperature. This helps the material adjust before being stretched tightly across the floor and fastened down along the edges.

Setting Up Your Stapler

Carefully inspect your air stapler before connecting it. Check for obstructions or debris in the fastener channel. Confirm proper adjustment controls depending on carpet backing thickness. Insert an initial fastener strip by pulling back the spring-loaded pusher guide until it locks, then sliding staples into the channel and releasing the guide.

Always use regulated compressed air when powering a pneumatic stapler. An optimal pressure range for flooring tools is 70 to 100 PSI. Too little pressure risks incomplete sealing while too much can damage tack strips or propel fasteners through the carpet completely.

Connect the air hose securely before turning supply pressure on or off. Be sure to verify the trigger and safety lock mechanisms are functioning properly too. Briefly test-fire into scrap material. Adjust driving depth based on how deeply staples penetrate the scrap backing.

Stapling Down Carpet

Once prep work is done, you're ready to start fastening the carpet along walls and transitions using your pneumatic stapler. Position the stapler flush against the wall surface to drive fasteners directly into the tack strip rather than angling them outward. Consistently check underlayment adhesion and reactivate bonding glue residues as you go.

Deploy staples in consistent intervals 2 to 3 inches apart. Overlap fasteners slightly with the preceding staple to form dense securing clusters. Be particularly diligent sealing corners and around doorway transitions then reinforce edges subject to extra stress with additional staple rows.

Take care not to damage base trim or moldings with the stapler tip. Temporarily remove decorative elements if needed to get the tool head flush with walls. Refasten them securely afterward. For best results, carefully double check all around the perimeter for loose seams, bubbles or stretched areas after completing initial fastening.

Safety Tips

Always disconnect the stapler from supply lines before making adjustments, clearing jams or moving away from the active work area. Don't point it toward yourself or others when reconnecting pressure. When not is active use, disengage the safety lock.

Use eye protection during operation. Keep hands and body parts away from the ejection pathway. Never rest your finger on the trigger unless actively driving a staple. Similarly, stay alert to maintain proper positioning rather than overextending your reach.

Take the RONGPENG 9040C Ga18 Narrow Crown Stapler into your toolkit, for seamless carpet installation. This pneumatic stapler is built for high efficiency, simple structure, easy operation, convenient maintenance.

360°Adjustable Exhaust Vent, allows users to direct air away from their face. Trigger and grip are more comfortable on your wrist and fingers. With quick release nose, easy to clean the jammed nails. high capacity magazine and reduces downtime. It drives Ga.18 staple from 16mm to 40mm length.

It is widely used in carton making, packaging, furniture, decoration, leather and woodworking industries.

 Specification:

Model:9040C

Dimension:54x242x248mm

Weight:1.45kg(3.1Lb)

Required Pressure:70-110PSI(4.8-7.5bar)

Max.Pressure:120PSI(8.3bar)

Nail Capacity:100PCS

RONGPENG has quickly risen to become an unrivaled global producer of air-powered devices including air tools, air spray gun, air nailer, airless paint sprayer, and etc.

RONGPENG seeks independent sales agent to represent and market our industry-leading pneumatic tools. We support OEM, ODM, OBM customization, small order quantity is acceptable and samples are available.

Make any cooperation possible. Any services related to the product, inquire with us now! Rongpeng@Rongpeng.Com